Recover Failed Hard Drive Using Basic Steps
It is quite disheartening to realize that your hard drive just stopped working without any prior warning. Worse is when there was no clicking, screeching or popping sounds from your system. Then it just happens when there is very important data that has not been stored in any other device. This calls you to recover failed hard drive because when that is not done, the information stored may be lost forever and perhaps if this is priceless information, there is no otherwise. But before you begin to start any recovery options, the first step is to read all the warnings as this is very important, otherwise, something could go seriously wrong.
To recover failed hard drive, one could begin by inspecting the hard drive for any possible damage. You remove the hard drive from the computer or any other device. Check carefully for any damage on the external controller board. Find out if there are any broken parts. Move it gently as you listen to any metallic noises. If there are, you may have to check with a data recovery specialist in the event that the data is of immense importance to you. At the same time, you may decide to go it alone by plugging the hard drive in with a new cable that is known to be working.
For those who have PATA drive, you could switch drive pin settings to recover failed hard drive. For example, if it was slave or cable select, it could be changed to master. It should be plugged in without any other device on the port before trying again. see more:
Recover Failed Hard Drive By Replacing The Drive’s Controller Board
There is the option of replacing the drive’s controller board to recover failed hard drive. This is done by first inspecting the drive’s controller board carefully to see if it is possible to remove it without exposing its platters. This is only possible for those drives that have externally mounted controller board. If this is not so, it is prudent not to go further and seek professional help. Next, is to find a sacrificial drive. When doing this, it is necessary to find the same model number. To match drives, one may need to go to places like ebay, or check a photo from an auction to find out if the model matches the firmware. To be too sure, find out from the person selling if indeed this is what you want.
The next process to recover failed hard drive is to remove the controller board of the failing drive using the correct screw drivers. When using them, one ought to be careful, as the screws are rather soft. While at it, learn how to connect it to the drive. Since most drives are connected via ribbon cables and pin rows, it pays to be gentle to avoid damaging the connectors. Carefully remove the controller board from the working drive before attaching the working board to the failing drive.
More hard drive recovery tips here-
http://www.harddriverecovery.org
To recover failed hard drive, one could begin by inspecting the hard drive for any possible damage. You remove the hard drive from the computer or any other device. Check carefully for any damage on the external controller board. Find out if there are any broken parts. Move it gently as you listen to any metallic noises. If there are, you may have to check with a data recovery specialist in the event that the data is of immense importance to you. At the same time, you may decide to go it alone by plugging the hard drive in with a new cable that is known to be working.
For those who have PATA drive, you could switch drive pin settings to recover failed hard drive. For example, if it was slave or cable select, it could be changed to master. It should be plugged in without any other device on the port before trying again. see more:
Recover Failed Hard Drive By Replacing The Drive’s Controller Board
There is the option of replacing the drive’s controller board to recover failed hard drive. This is done by first inspecting the drive’s controller board carefully to see if it is possible to remove it without exposing its platters. This is only possible for those drives that have externally mounted controller board. If this is not so, it is prudent not to go further and seek professional help. Next, is to find a sacrificial drive. When doing this, it is necessary to find the same model number. To match drives, one may need to go to places like ebay, or check a photo from an auction to find out if the model matches the firmware. To be too sure, find out from the person selling if indeed this is what you want.
The next process to recover failed hard drive is to remove the controller board of the failing drive using the correct screw drivers. When using them, one ought to be careful, as the screws are rather soft. While at it, learn how to connect it to the drive. Since most drives are connected via ribbon cables and pin rows, it pays to be gentle to avoid damaging the connectors. Carefully remove the controller board from the working drive before attaching the working board to the failing drive.
More hard drive recovery tips here-
http://www.harddriverecovery.org